Recommended Network Settings for VOIP

Recommended Network Settings for VOIP

In This Article:

We recommend that a qualified network professional configure these advanced settings on end-user networking devices. The below settings are recommendations and should be implemented with careful consideration. AVATAVA is not responsible for any disruption to network services that may result in implementing these recommendations.

The following information, referenced in the AVATAVA Master Service Agreement (Section 5.4.1), is what AVATAVA considers to be "the minimum requirements" for operating VoIP over a network. AVATAVA does recommend the implementation of QoS (Quality of Service) mechanisms such as class-of-service and flow-control or the utilization of VLANs across your network.

Services To Disable

SIP ALG (Application Layer Gateway) functions such as SIP Transformations, SIP Application Helpers, SIP Normalization, etc. AV Client Enforcement on any IP assigned to an endpoint Content Filtering on any IP assigned to an endpoint

Services To Enable

Bandwidth Management/Traffic Shaping Default UDP session timeout to 300 seconds Consistent NAT (On Sonicwall devices) Inbound and outbound traffic on ports and subnets listed below DNS resolution on endpoints

Subnets To Whitelist and Ports To Open

AVATAVA Public Subnets

IPv4

  • 8.2.200.64/28
  • 69.166.104.64/28
  • 69.166.106.16/28

IPv6

  • 2605:3ac0:100::1/56

AVATAVA Required Ports

Port Protocol Application 80 TCP HTTP 443 TCP HTTPS 2195 TCP SSL 5060 TCP and UDP SIP 5061 TCP and UDP SIPS 9002 TCP WebSockets 20000-27999 UDP RTP

Information regarding the application each port is for can be found in the knowledge base article: Ports Used By the AVATAVA Cloud Switch

Bandwidth Requirements

AVATAVA primarily utilizes the G.711 μ-law codec for VoIP traffic. Voice traffic is sampled at 8kHz frequency with 8-bit samples requiring 64kbit/s in both directions (the upload traffic representing your spoken audio and the download traffic representing the callers audio). To give plenty of overhead to the call (and accommodate for improvements in the G.711 protocol) we recommend 100kbit/s of allowance per concurrent call. So if 5 simultaneous calls are expected, a total of 500kbit/s should be available for VoIP calling to guarantee an error-free, high-quality call.

Packet Measurements

The following measurements are an integral part of the Mean Opinion Score (MOS) measured by the AVATAVA Softswitch. Calls should stay above a 4.0 measured MOS score to maintain a great audio experience. For more information regarding MOS scores, please review Mean Opinion Score (MOS)

Packet Delay

Packet Delay, often referred to simply as latency, refers to the amount of time it takes for a packet to be transmitted across a network from source to destination. For VoIP, high delay can be disruptive because it impedes the synchronicity of a conversation, often causing speakers to ‘step’ on one another. While a small amount of delay is unavoidable in Ethernet-based networks, problems can occur when the delay is not uniform from packet to packet or is too long. For acceptable voice quality, packet delay should be below 70 milliseconds (70ms) each way.

Packet Delay Variance

Packet Delay Variance, or jitter, is the variation in packet delay caused by the routing of Ethernet packets through the network. In general, higher levels of packet delay are more likely to occur on either slow or heavily congested links. Most VoIP endpoints have a jitter buffer to put packets back in order before being played to the listener, but these are often limited in size. For acceptable voice quality, packet delay should be below 10 milliseconds (10ms).

Packet Loss

Packet Loss is the percentage of packets transmitted from the source to the destination that "does not make it" due to factors on the Ethernet network. As packet loss increases, encoded audio is not being received at the destination which may cause odd audio "artifacts" including static, echo, and the total loss of audio in short segments. Packet loss should stay below 5% of 100 ~1500 byte packets to maintain acceptable audio quality.

  • VOIP, VOIP Network Settings
  • 2 utilizatori au considerat informaţia utilă
Răspunsul a fost util?

Articole similare

Call Forwarding Using Star Codes

Call forwarding allows a user to forward a call received depending on the call forwarding type,...

Preparing for the Customer Onboarding Journey

Business Customer Onboarding Journey As a business customer is preparing to onboard, you must...

How To View System Users

A system user is a user that is created alongside and owns an application. These users provide...

Enable Web Management And Change Admin Password Via Device Override

In This Article: Avaya Overrides Cisco Overrides Grandstream Overrides Obihai (Polycom ATA...

Is the AVATAVA Cloud Switch HIPPA Compliant?

One of the key concerns from business customers in the medical field is compliance with the...